All machines have service life, AOL digital cardboard cutting machine is no exception, if the machine is properly used to extend the service life is possible.
Small surface to introduce you a few methods, hope to extend your cutting machine service life to help.
Pay attention to the environment of cutting machine
It is suggested that the cardboard glass cutter should be placed in a place without direct sunlight or other heat radiation, because the sun is too strong, the surface of the machine will overheat, which is not conducive to the maintenance of the machine.
Besides, the surrounding environment should not be too wet. The bed of the paperboard cutting machine is made of metal. The excessive humidity will make the cutter rust easily, the running resistance of metal guide rail increases, and the cutting speed is reduced.
Do not put it in places with too much dust or corrosive gas, because these environments are easy to damage the electronic components of board cutting machine, or cause poor contact and short circuit between components, thus affecting the normal operation of the equipment.
Standard operation of automatic cardboard cutting machine
According to the correct operation process, it is also the basic measure to guarantee the prolongation of the life of the board cutter. All our machines have operation instructions and special after-sales personnel to train you one-on-one. Operation according to the specification can reduce the failure rate of equipment.
It is recommended that the operator use the equipment after training. If the equipment fails, contact AOL after-sales personnel for the first time to let them tell you the correct handling method. We will provide video connection service, which can remotely command you how to repair. Of course, it is also possible to find local professional technicians for maintenance. Do not disassemble and disassemble them without permission to aggravate the failure degree of equipment or secondary failure.
Normal shutdown
When you shut down, turn off the main power button. Do not force shutdown, do not power off suddenly. When the machine is working normally, if the power is suddenly cut off, the hardware, especially the hard disk, will be damaged due to the graphic layout and recognition operation of the extremely hot software.
Pay attention to the protective shell
In general, avoid bumps and avoid irritating corrosive liquid contamination. When cleaning the housing is required, wipe with a wet cloth that is screwed dry or use a soft cloth dipped in a special cleaner.
Avoid sharp objects from touching the housing. When switching the cutter head, care should be taken to insert and pull it gently to avoid damaging the shell accidentally.
Regular machine maintenance
Carry out regular maintenance according to the maintenance procedures and frequency in the instruction manual, pay attention to the time of lubricating oil and cleaning the oil pot.
- every working day, the dirt of machine tool and guide rail must be cleaned to keep the bed clean, turn off the air source and power supply when off work, and drain the remaining gas in the pipe belt of the machine tool.
- if the machine is left for a long time, turn off the power supply to prevent the non professional operation.
- if the machine is left for a long time, turn off the power supply to prevent the non professional operation.
Check whether the zero point, limit switch and bump mounting screw of x-axis, Y-axis and z-axis are loose and whether the limit switches of each axis are sensitive.
- after daily work is completed, open the water release valve of the air storage cylinder at the bottom of the air compressor for drainage. After the waste water is discharged, close the water release valve.
So what are the precautions for the aol cnc cardboard cutter?
- When the cardboard cutterplotteris powered up or in operation, please do not contact any electronic components in the electrical cabinet and operating table, so it is easy to send the electric shock site.
- Please do not operate the switch button of any AOL cardboard flatbed cutter by wet hand to prevent electric shock.
- Please do not live to carry out inspection line or replace electronic components, responsible for electric shock or injury.
- When moving the machine, pay attention to lifting the foundation, let the safety wheel fall to the ground and push it！
Above is about AOL cardboard cutting machine maintenance and operation procedures, if you know more, welcome to leave a message on the website or send to the email [email protected].
https://www.youtube.com/channel/UCDiNQSjBR5DsAX9QfkWF7AA?view_as=subscriber
https://www.facebook.com/AOL-CNC-1984243318542126/?ref=pages_you_manage
